Skip to Content

Changes for page Prusa Slicer

Last modified by Josh McGee on 2025/11/08 03:20
From version 18.1
edited by Josh McGee
on 2025/11/08 03:18
Change comment: There is no comment for this version
To version 16.1
edited by Josh McGee
on 2025/11/08 03:12
Change comment: There is no comment for this version

Summary

Details

Page properties
Content
... ... @@ -40,26 +40,24 @@
40 40  === ===
41 41  
42 42  The orientation of your 3D print is important because each layer is supported by the one beneath it. For example if you were 3D printing a pyramid, you would ideally want the base of the pyramid to be the base of the 3d print. Use the (% class="mark" %)##Rotate##(%%) command to rotate your part if you need to.
43 -\\
43 +\\??? image goes here: The rotate command can be found in the panel on the left
44 44  
45 -[[The rotate command can be found in the panel on the left>>image:image1.png||alt="The rotate command can be found in the panel on the left" data-xwiki-image-style-alignment="center" height="500px" width="325px"]]
46 46  
47 -
48 48  If your design needs to have overhanging or unsupported pieces, then you have two main options:
49 49  1) Have the slicer add in supports which can be broken off once the print is finished. To do this make sure the (% class="mark" %)##Supports##(%%) dropdown is not (% class="mark" %)##None##(%%).
50 50  2) Use the (% class="mark" %)##Cut##(%%) command to cut your part into pieces that could each be printed like a pyramid. For example a sphere would be very difficult to print and would require a lot of supports, but if you cut the sphere in half each half could act effectively as a pyramid and would be very simple to cut. When the print is finished, the two halves can then be glued together.
51 51  
52 52  
53 -[[image:image2.png||data-xwiki-image-style-alignment="center" height="268px" width="500px"]]
51 +??? image goes here
54 54  
55 55  ===
56 56  \\Other printing options ===
57 57  
58 58  
59 -[[image:image20.png||data-xwiki-image-style-alignment="center" height="258px" width="500px"]]
60 60  
61 -[[image:image17.png||data-xwiki-image-style-alignment="center" height="278px" width="500px"]]
58 +??? 2 images go here
62 62  
60 +
63 63  === Export G-Code ===
64 64  
65 65  
image1.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.josh_mcgee_g
Size
... ... @@ -1,1 +1,0 @@
1 -20.5 KB
Content
image17.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.josh_mcgee_g
Size
... ... @@ -1,1 +1,0 @@
1 -1020.2 KB
Content
image2.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.josh_mcgee_g
Size
... ... @@ -1,1 +1,0 @@
1 -955.4 KB
Content
image20.png
Author
... ... @@ -1,1 +1,0 @@
1 -XWiki.josh_mcgee_g
Size
... ... @@ -1,1 +1,0 @@
1 -901.9 KB
Content